Buoyancy Factor Calculation

Buoyancy Factor is the factor that is used to compensate loss of weight due to immersion in drilling fluid.

Before explaining any further, I will explain you about the basic concept of Buoyancy. Buoyancy is the upward force that keeps things afloat. The net upward buoyancy force equals to the amount of the weight of fluid displaced by the body volume. This force will make objects lighter when it immerses in fluid. For example, we feel ourselves lighter when we are in swimming pool because this is the effect of buoyancy.

bouyancy-factor

In drilling operation, we need to know how much weight of string of drill pipe, completion string, etc in drilling fluid. Therefore,  Buoyancy Factor is value that we need to know and be able to calculate this value. Please follow the formulas below to calculate Buoyancy Factor in different mud weight units, ppg and lb/ft3.

Buoyancy Factor using mud weight in ppg

Buoyancy Factor (BF) = (65.5 – mud weight in ppg) ÷65.5

Note: 65.5 ppg is density of steel.

Example: Determine the buoyancy factor for a 13.0 ppg fluid:
BF = (65.5 – 13.0) ÷ 65.5
BF = 0.8015

Buoyancy Factor using mud weight in  lb/ft3

Buoyancy Factor (BF) = (489 – mud weight in lb/ft3) ÷489

Note: 489 lb/ft3 is density of steel.

Example: Determine the buoyancy factor for a 100 lb/ft3 fluid:
BF = (489 – 100) ÷489
BF = 0.7955

How to use the Buoyancy Factor

In order to figure out the actual weight of drilling string in mud, the air weight of drilling string times the buoyancy factor equal to actual weight in mud, called buoyed weight.

Example: Determine the string weight in 13.0 ppg mud. Air weight of string is 350 klb.

The buoyancy factor for a 13.0 ppg fluid:
BF = (65.5 – 13.0) ÷ 65.5
BF = 0.8015

Buoyed weight of drill string = String weight in the air x BF

The buoyed weight of drill string in 13.0 ppg mud = 350 x 0.8015 = 280.5 Klb.

Ref books: Lapeyrouse, N.J., 2002. Formulas and calculations for drilling, production and workover, Boston: Gulf Professional publishing.

Bourgoyne, A.J.T., Chenevert , M.E. & Millheim, K.K., 1986. SPE Textbook Series, Volume 2: Applied Drilling Engineering, Society of Petroleum Engineers.

Mitchell, R.F., Miska, S. & Aadny, B.S., 2011. Fundamentals of drilling engineering, Richardson, TX: Society of Petroleum Engineers.

Related Post

Calculate inner capacity of open hole/inside cylin... From the previous post, you learn how to calculate annular capacity and this post shows you how to use the same principle to calculate inner capacity ...
Volume of Cutting Generated While Drilling While drilling, cuttings are generated every footage drilled and this topic will demonstrate how to determine volume of cutting entering into the well...
Amount of cuttings produced per foot of hole and t... After learning about capacity calculation, we can apply the capacity calculation to determine how much barrels of cutting produced per foot of hole dr...
Determine surge and swab pressure for close-ended ... I would like to show more calculation about surge and swab pressure. In this article, I will show how to use the previous formulas (Surge and swab pre...
Share the joy
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  

About DrillingFormulas.Com

Working in the oil field and loving to share knowledge.
Tagged . Bookmark the permalink.

22 Responses to Buoyancy Factor Calculation

  1. Hi, during drilling process we need to know how much weight of string of drill pipe, completion string, etc in drilling fluid. Buoyancy Factor is value that we need to know and be able to calculate this value.

    Regards

  2. kingsley says:

    please i need write up on evaluation of drilling bit performance

  3. URL says:

    It is hard to locate knowledgeable folks on this subject, but you sound like you know what you are talking about! Thanks 537099

  4. sam soh says:

    what happens if my well is completed with a 12.1 ppg completion fluid, i then go on to displace tubing fluid to 10.3 ppg. how do i find out the wet weight of the tubing string ? displacing of tubing fluid occurs before packer has set.

    • Your weight showing in the weight indicator will slightly increase because of reduction of density. In order to get the weight in the completion fluid, you determine the new buoyancy factor using 10.3 ppg and multiply by string weight.

      Regards,
      Shyne.

  5. Rinat says:

    Is there a difference between weight of the drill string and weight of the drill string in air? Thank you!

  6. Leon says:

    How do you calculate the bouyoncy force on the cutting of weight 8.33 ppg and the volume of mud is 3 in3 with a weight of 11ppg

  7. Luciano says:

    What is the 65,5 on the formula for bouyancy fator?

  8. Mero says:

    How the buyouancy factor affect the string Wt if the string is stinged into packer?

  9. ddan says:

    There are US and UK types of pounds per gallon density. Which one can be used in buoyancy factor calculation?
    Thanks

  10. Sai says:

    why is the buoyant weight of drill string important?
    Does it play a role in the load provided/rotary motion provided.

  11. guest says:

    Very Important Note. This formula for unplugged pipe at the bottom.

Leave a Reply

Your email address will not be published. Required fields are marked *