What Cause Lost Circulation in Drilling Leading to a Well Control Situation

Lost circulation whole mud (whether to depleted reservoirs or to natural/induced fractures)is one of biggest causes of well kicks. In the wellbore, fluid levels can decrease and this lowers the hydrostatic pressure. Once hydrotatic pressure is less than formation pressure, it will cause a flow from the formation in permeable zones. Figure 1 illustrates loss of fluid level into a weak zone which will lead a well control incident if a wellbore is not filled up on time with correct mud weight.

Lost Circulation in Drilling Leading to a Well Control Situation

Figure 1 – Lost Circulation in Drilling Leading to a Well Control Situation

Lost circulation can happen for a number of reasons and we’ve detailed four possibilities below;

Annular Circulating Friction

When drilling near the fracture gradient of the formation with a heavy mud, the pressure added by circulating friction should always be considered. Especially in small holes with a large drill pipe or with stabilizers inside the protective casing, this added pressure can be significant. In many cases, the pumping rate will need to be reduced to then decrease the circulating pressure. Often, where high gel fluids are used, the problem quickly becomes acute when attempting to break circulation in this way.

Entering the Hole Too Quickly

When the drill pipe and bottom assembly are lowered too quickly, this can also cause a loss of circulation (this includes the reamers, drill collars, and bit). Although somewhat similar to swabbing, it’s effectively in reverse as the weakest formation is targeted by the piston action as it forces the drilling fluid into new positions. If the pipe is much larger than the hole and the string has a float in it, the problem is made even worse. Whenever weaker formations have been exposed, or even if heavy mud has been employed to counter high formation pressure, particular care will need to be taken when running pipe into the hole. Many commercially available programs now exist for surging calculations which makes the whole process easier than ever before.

Balled-Up or Sloughing Tools

To restrict the flow of fluids in the annulus, it’s possible to partially plug the annulus by sloughing shale. By imposing a backpressure on formations, a breakdown can quickly occur as long as the pumping continues. Stabilizers and other large drillstring components are common locations for annular plugging; the chances of encountering this type of lost circulation can be reduced with efforts to reduce balling. Read more details about balled up bit below.

Balled up Bit

Balled up Bit

Excessive Mud Weight

Finally, fluid levels in the hole can decrease and circulation can be lost whenever the fracture gradient (of the weakest exposed formation) is outweighed by bottomhole pressure. Why? Because the effectiveness of the hydrostatic head will decrease when acting against those formations that haven’t broken down. Assuming the mud levels drop severely, the BHP can fall below formation pressure and the well will start flowing.

Lost circulation should be avoided at all costs; if returns cease, measured volumes of water should be pumped into the hole and this should minimize the loss of hydrostatic pressure. For the Drilling Site Supervisors, they need all volume measures so they can calculate the weight of mud required to support the formation before fracturing occurs. After gaining returns, the well will need to be checked to ensure it isn’t flowing alone.

We hope this article help you prevent lost circulation in the future. Please feel free to share your thought in the comment box below.

References

Cormack, D. (2007). An introduction to well control calculations for drilling operations. 1st ed. Texas: Springer.

Crumpton, H. (2010). Well Control for Completions and Interventions. 1st ed. Texas: Gulf Publishing.

Grace, R. (2003). Blowout and well control handbook [recurso electrónico]. 1st ed. Paises Bajos: Gulf Professional Pub.

Grace, R. and Cudd, B. (1994). Advanced blowout & well control. 1st ed. Houston: Gulf Publishing Company.

Watson, D., Brittenham, T. and Moore, P. (2003). Advanced well control. 1st ed. Richardson, Tex.: Society of Petroleum Engineers.

 

Related Post

Adjusted maximum allowable shut-in casing pressure You calculate the maximum initial shut-in casing pressure (MISICP) based on the original mud weight before you start drilling ahead. Once you drill de...
Post Shut-In Procedures while Drilling There are several figures that must be recorded after the well has been properly shut in in case of a well control situation.   Shut-In Cas...
Kick Tolerance Concept and Calculation for Well De... Kick tolerance is the maximum gas volume for a given degree of underbalance which the circulation can be performed without exceeding the weakest forma...
Trip Tank and Its Importance to Well Control Trip tank is a small tank which has a capacity of 20 – 50 bbl and its shape is tall and shallow because it can effectively detect volume changes. The ...
Share the joy
  • 203
  •  
  • 1
  •  
  •  
  •  
  •  
  •  
  •  
    204
    Shares
Tagged , . Bookmark the permalink.

About DrillingFormulas.Com

Working in the oil field and loving to share knowledge.

One Response to What Cause Lost Circulation in Drilling Leading to a Well Control Situation

  1. James Wagner says:

    The mud should be in good condition well before getting into loss circulation zones, note driller should after making a connection lower the tool joint just below the rotary table bushing so if there is any packing off around the top of the drill collars this will enable circulation to break much easier and ease into it with the pump

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.