Working on the rig both offshore and onshore always involves lifting operation using rig cranes or mobiles crane. Therefore, hazards associated with lifting operation must be carefully taken into account. We would like you to watch and learn from this video in order to understand risk of overloading the mobile crane and the final result. We wish this video would raise use some concerns regarding safe work practices while working with cranes.
Some safety tips about a mobile cranes are listed below;
10 Tips for Better Mobile Crane Operations by Randy Burbach
1. Never override the mobile crane’s computer.
2. Be aware of all overhead hazards – specifically close-by buildings and any power lines that are within the zone of operation.
3. Read the load charts – prior to turning the key in any new mobile crane.
4. Cell phones in the cab – while the crane’s key is on the cell phone is off.
5. Always note the changing conditions on the jobsite – from personnel to weather to surroundings.
6. Sometimes in a working situation, the crane operator needs to stop, evaluate, and find a safer lift plan.
7. Check ground conditions – before crane setup, ensure that the site is suitable to support your mobile crane and the future suspended loads.
8. Use appropriate pads & cribbing – mobile crane operators need to make sure they are using correct pads or cribbing to avoid having an outrigger fail or sink when they are making a lift.
9. Before starting your crane, always double check the oil, gas, and other fluid levels.
10. At the beginning of your shift, walk-around your crane checking for mechanical, electrical, structural, and hydraulic issues (MESH).
Lifting operations – cranes by http://www.hse.gov.uk/
What you need to do
The law says that all lifting operations involving lifting equipment must be properly planned by a competent person; appropriately supervised; and carried out in a safe manner.
Cranes and lifting accessories such as slings must be of adequate strength, tested and subject to the required examinations and inspections.
All crane operators, and people involved in slinging loads and directing lifting operations, must be trained and competent.
There are four key aspects to the safe use of cranes:
- Planning lifting operations
- Safe systems of work
- Supervision of lifting
- Thorough examination
What you need to know
Tower and mobile cranes are used extensively on construction projects and present two principal hazards:
Collapse of the crane – such incidents present significant potential for multiple fatal injuries, both on and off-site;
Falling of the load – these events also present a significant potential for death and major injury.
Other incidents have involved people being struck by moving loads, cranes contacting overhead conductors and cranes colliding with each other.
Planning lifting operations
All lifting operations should be planned so they are carried out safely with foreseeable risks taken into account.
The person appointed to plan the lifting operation should have adequate practical and theoretical knowledge and experience of the lifts being undertaken.
The plan will need to address the risks identified by a risk assessment, the resources required, procedures and the responsibilities so that any lifting operation is carried out safely.
The plan should ensure that the lifting equipment remains safe for the range of lifting operations for which the equipment might be used.
British Standard BS 7121Part 1 2006 sets out an acceptable standard for managing lifting operations using cranes on construction projects.
Safe systems of work
You must plan lifting operations carefully to ensure they are carried out safely. Your plan should result in a safe system of work which may need to be written down if it is a complex lift. This record is sometimes known as a method statement and you must ensure that everyone involved understands it.
Key elements include:
- planning – including site preparation, crane erection and dismantling;
- selection, provision and use of a suitable crane and work equipment
- including safe slinging and signalling arrangements;
- maintenance and examination of the crane and equipment;
- provision of properly trained and competent personnel;
- supervision of operations by personnel having the necessary authority;
- thorough examinations, reports and other documents;
- preventing unauthorised movement or use of the crane; and
- measures to secure safety of persons not involved in the lifting.
Supervision of lifting
The right level of supervision must be in place for lifting operations, reflecting the degree of risk and personnel involved in the particular lifting operation.
The crane supervisor should direct and supervise the lifting operation to make sure it is carried out in accordance with the method statement.
The crane supervisor should be competent and suitably trained and should have sufficient experience to carry out all relevant duties and authority to stop the lifting operation if it is judged dangerous to proceed.
Thorough examination
There are strict legal requirements concerning the thorough examination of all cranes:
Lifting equipment must be thoroughly examined at the prescribed intervals. This is a detailed and specialised examination by a competent person.
The examination will usually be arranged by the crane hire company, although it is the responsibility of the crane user to ensure that all necessary examinations are carried out and that the required reports are in order.
Records of thorough examinations and tests must be: readily available to enforcing authorities; secure; and capable of being reproduced in written form.
Ref: http://www.hse.gov.uk/construction/safetytopics/cranes.htm
http://www.iti.com/Crane-and-Rigging-Success/bid/58758/10-Tips-for-Better-Mobile-Crane-Operations
Thank you so much for the advice to check the conditions of the ground before setting up a crane for lifting. I feel like the potential for accidents if you’re on unstable ground with a crane are very large, so this sounds like something that should never be skipped. I bet that hiring only licensed and certified crane operators would be one good way to ensure that this always happens.